How Much Does It Cost To Repair A Receiver Speaker On Iphone 7 Plus

Introduction

The iPhone 7 Plus earpiece speaker also performs double duty as a loudspeaker, providing stereo sound. If your earpiece speaker is acting up, follow this guide to remove and replace information technology.

Before you begin, discharge your iPhone battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.

Before you brainstorm, discharge your iPhone battery below 25%. A charged lithium-ion bombardment can grab fire and/or explode if accidentally punctured.
Ability off your iPhone before get-go disassembly.
Remove the two 3.4 mm pentalobe screws at the lesser border of the iPhone.
Opening the iPhone's brandish will compromise its waterproof seals. Have replacement seals prepare before you proceed past this step, or accept intendance to avoid liquid exposure if you reassemble your iPhone without replacing the seals.

Heating the lower edge of the iPhone will help soften the adhesive securing the display, making it easier to open.

Heating the lower edge of the iPhone will aid soften the adhesive securing the display, making it easier to open up.
Use a hairdryer or set up an iOpener and utilise it to the lower border of the iPhone for almost a infinitesimal in order to soften upward the adhesive underneath.

Apply a suction cup to the lower half of the front panel, but in a higher place the home button.
Exist sure the suction loving cup does non overlap with the home button, as this will prevent a seal from forming between the suction cup and forepart glass.
If your display is desperately cracked, roofing information technology with a layer of clear packing tape may let the suction loving cup to adhere. Alternatively, very stiff tape may exist used instead of the suction loving cup. If all else fails, you lot can superglue the suction loving cup to the broken screen.

Pull up on the suction cup with firm, constant pressure to create a slight gap between the forepart console and rear case.
Insert the flat end of a spudger into the gap.
The watertight adhesive holding the display in place is very strong; creating this initial gap takes a meaning corporeality of force. If yous're having a hard time opening a gap, rock the screen upward and down to weaken the agglutinative until yous tin can fit a spudger inside.
While pulling up on the suction cup, twist the spudger to widen the opening betwixt the screen and rear example.

Insert the flat end of the spudger between the front panel and the rear case at the lower left edge of the iPhone.
Slide the spudger up the left edge of the phone starting at the lower edge and moving towards the volume command buttons and silent switch, breaking up the adhesive holding the display in place.
Do not try to pry the top edge of the display abroad from the rear instance, as information technology is held in place past plastic clips that may suspension.

Remove the spudger from the left side of the telephone and insert the flat end into the bottom correct corner.
Slide the spudger up the correct edge of the phone to the top corner, breaking upward the agglutinative property the brandish in place.

Pull up on the suction loving cup to lift up the brandish and open the iPhone.
Do not enhance the display more than 10º every bit there are delicate ribbon cables forth the right border of the device connecting the display to the logic board.

Pull upwards on the small nub on the suction cup to remove information technology from the front panel.

Slide an opening pick underneath the display forth the top edge of the phone to loosen the final of the adhesive.

Pull the brandish associates slightly away from the top edge of the phone to disengage the clips holding it to the rear case.
Open the iPhone past swinging the display up from the left side, similar the back comprehend of a book.
Don't effort to fully separate the display yet, as several frail ribbon cables notwithstanding connect information technology to the iPhone's logic board.

Remove the following four tri-signal Y000 screws securing the lower display cable bracket to the logic board:
Three 1.ii mm screws
One 2.6 mm screw

Remove the lower display cablevision bracket.

Utilise the point of a spudger to lift the battery connector out of its socket on the logic board.
Curve the connector cable up slightly to prevent it from making contact with the socket and providing ability to the telephone.

Make sure the bombardment is disconnected before you disconnect or reconnect the cables in this pace.
Use the flat end of a spudger or a fingernail to disconnect the two lower brandish connectors by prying them straight up from their sockets on the logic board.
To re-attach printing connectors, press downwardly on 1 end until information technology clicks into place, then repeat on the other end. Exercise non press down on the middle. If the connector is even slightly misaligned, the connector tin can bend, causing permanent damage.
If you lot have a blank screen, white lines on the display, or partial or consummate lack of touch response afterward reassembling your telephone, try disconnecting and carefully reconnecting both of these cables and make sure they are fully seated.

Remove the three tri-bespeak Y000 screws securing the bracket over the front end console sensor assembly connector:
One 1.3 mm spiral
Two 1.0 mm screws
Remove the bracket.

Disconnect the front end panel sensor assembly connector from its socket on the logic board.
This printing connector should also be reconnected one terminate at a time to minimize the risk of bending.

Remove the display assembly.
During reassembly, interruption here if you lot wish to supercede the adhesive around the edges of the display.

Remove the five Phillips screws securing the earpiece speaker bracket:
Two i.8 mm screws
One two.3 mm screw
I 2.four mm screw
One 2.8 mm screw

Remove the earpiece speaker bracket.

Use the flat stop of a spudger to lift the front end-facing camera from its housing.
Gently bend the camera ribbon cable to the side to clear the mode to the earpiece speaker underneath.

Remove the earpiece speaker.
Don't touch on the four spring contacts with your fingers—your pare oils may cause a malfunction. If accidentally touched, clean the contacts gently with isopropyl alcohol (90% or higher).

Conclusion

Compare your new replacement part to the original part—you may need to transfer remaining components or remove agglutinative backings from the new part earlier installing.

To reassemble your device, follow the to a higher place steps in reverse lodge.

Accept your due east-waste to an R2 or east-Stewards certified recycler.

Repair didn't go every bit planned? Try some bones troubleshooting, or search our Answers forum for help.

Team

Embed this guide

Choose a size and copy the code beneath to embed this guide as a pocket-sized widget on your site / forum.

Preview