How To Repair Warped Cast Iron Cookware

Download Article

Download Commodity

Warped pans are a mutual problem in many kitchens. Warping occurs as the outcome of rapid temperature changes, and this happens more frequently in lower quality pans. Repairing your pan tin can be difficult (perhaps even unsafe), and should be washed with caution. In that location are also some steps you can take, such as heating and cooling your pans gradually, to preclude warping in the offset place.

1

Check the warranty. Many pans (especially higher cease cookware) will come with a warranty that may cover warping. If your pans came with a warranty, double check the conditions. You lot may be able to receive a replacement, and save yourself the trouble of flattening.^[1]
two
Cutting a piece of wood to match the diameter of your pan. In gild to repair the warping of your pan, you are going to need a slice of wood. Purchase a 2 X iv (45 Ten xc mm) from your local hardware store, and cut to it to fit the diameter of your pan.^[two]
- Yous can use either a round saw or regular handsaw to cut your ii X 4 to length.
- Many hardware stores will cut 2 10 iv'southward to length for yous. Ask well-nigh this at the store.
- Ever habiliment safety goggles when cutting forest.
- If your pan has bowed outwardly, the piece of wood tin can be a chip longer than the pan.
- If your pan had bowed inwardly, the piece of forest must sit inside the pan.
Advertisement
three

Heat up your pan. Place your pan on the stove on medium to medium-loftier estrus. Wait 15-20 minutes, allowing the pan to get very hot. Taking care not to burn yourself, use a pot holder to remove the pan from the stove.^[three]
4

Place the pan on a durable surface. Set the hot pan down someplace sturdy and durable, with the bowed side facing up. If the pan is bowed outwardly, you have to rest the lip of the pan on a flat surface without assuasive the handle touch the surface. A stair or the demote of a picnic table tin can work.^[4]
5

Place the wood on the bowed side of the pan and beat the wood. Position your piece of wood across the center of the pan's crown (the place where it is most bowed). Use a mallet to bang on the slice of wood repeatedly. When the pan has cooled, it is time to finish.^[five]
6
Repeat this until the pan is flat. Render your pan to the stove top and reheat information technology. Then move it to a sturdy location, position the forest, and continue banging on it. It may take 3 to 4 rounds of this for you lot to see improvement in your pan.^[6]
- Straightened pans volition warp more easily than those which were never warped.
- Your pans will wear out from repeated warping and straightening, and will eventually need to be replaced.
Advertisement

i
Buy high quality cookware. Unfortunately, inexpensive pans are the almost likely to warp. Expect into higher quality cookware, and select pans that have a warranty. If you want to prevent your pans from warping, you need to choose cookware that has skillful heat conductivity. Yous'll also want something durable.^[7]
- Copper pans are known to take the best heat conductivity.
- Cast atomic number 26 pans accept longer to heat upward, but are very durable and unlikely to warp.
- Stainless steel pans tin can be stylish and durable, but these pans are the well-nigh likely to warp.
2

Heat up your pans gradually. Warping comes as the effect of rapid temperature changes. You tin protect your pans and help them to last longer by heating them up gradually. If you lot demand to cook something on high (or even medium) estrus, start past heating your stove to depression. Allow the pan to estrus up a little, then increase the temperature setting on your stove a couple of notches every few minutes.
three
Avert running hot pans under common cold water. Rapidly dropping temperatures can also cause pans to warp. Most commonly, pan warping occurs when you lot run a hot pan under common cold water. Never do this to your pans! Let your pans to cool off completely before adding them to water.
- If you accept been cooking at a very high heat, y'all may want to bring it downward to medium, and so low, before allowing to pan to cool naturally to room temperature.
Advertisement

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertising

Thanks for submitting a tip for review!

Well-nigh This Article

Article Summary X

If your pan's warped, y'all can repair it by heating it and striking it with a mallet. First, cut a piece of wood to the diameter of your pan. Rut your pan on medium-high heat for 15 minutes. When it'due south hot, identify your pan on a hard, durable surface. Then, place your wood in the pan, and hit the wood repeatedly with a mallet until it cools. It might accept you a few rounds of heating and hitting your pan, but before long plenty, it'll be flat again. If your pan came with a warranty, cheque if it's even so in date, since this might salvage you the effort. For more tips, including how to forbid you pans from warping, read on.

Did this summary help you?

Thanks to all authors for creating a folio that has been read 51,017 times.

Did this commodity aid you?